Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Parts & Accessories

$40.00
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 146mm - 1 axle per bag
$40.00
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 174mm - 1 axle per bag
$41.00
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many BMX hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 187mm - 1 axle per bag
$15.95
WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.
$9.00
- Replacement rear skewer - Spacing: 135mm - Material: Steel
$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
$18.00 - $22.95
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
$22.00
- SRAM, X9, Freehub Body, 11.2015.028.100
$58.00 - $75.00
Purchase our Kid Trailer axle for your bike, and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
$48.00
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
$54.00 - $59.95
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
$9.99 - $139.99
Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable
$21.00 - $26.99
These lightweight valves help prevent clogging from tubeless sealant. - Aluminum - 40mm length
$205.00 - $270.00
Replacement freehub kit for Hydra hubs
$6.70 - $10.95
Grade 10 chromium steel balls MR17287LLB - 17 x 28 x 7mm 6808LLB - 30 x 42 x 7mm
$6.18 - $9.79
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity
$47.70
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$47.70
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$24.60
DT Swiss tubeless ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type set ups. - Highly resistant adhesive tape works as a rim tape and airseal
$81.80 - $104.30
Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - End Cap Included
$24.00
Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).
$151.00
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum
$34.00
- Wheel axle rear Zipp 176D Disc Brake (axle only)
$24.00
Includes rim strip and tubeless tape for 1 wheel.
$70.00
- Wheel bearing kit front/rear - Bearing dimensions: 17 x 30 x 7mm - Material: steel - 2 pieces
$34.00
- Wheel Axle - Front
$19.00 - $31.00
Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.
$7.00
Package comes with two pieces of rim tape for use with the Zipp clinchers. Woven nylon material. Tape is extra thin with a thickness of 0.5 mm. Note: For Zipp 700c and 650c aluminum/carbon hybrid clichers, use the 16 mm rim tape. For Zipp 30 wheel set use 18mm but for the wider Firecrest and Firestrike carbon clinchers use the 20mm x 1/2mm rim tape.
Page 1 of 11 Next page